Module Keyence KV-H20

SKU: KV-H20
Hãng sản xuất: Keyence
Chất lượng: Mới 100%
Bảo hành: Chính hãng
Chứng từ: hóa đơn VAT

Dịch vụ kèm theo:
✓ Lập trình & Sửa chữa PLC Keyence theo yêu cầu
✓ Lắp đặt & vận hành tận nơi
✓ Hỗ trợ kỹ thuật trọn đời
Báo giá
Mã: KV-H20 Danh mục: ,
ModelKV-H20
General specificationsClassificationPositioning and high-speed counter unit
Power voltageMain unit side : supplied by the KV-700 CPU unit, I/O side : 24 VDC ±10%
Operating ambient temperature0 to +50°C (no freezing)*1*2
Operating ambient humidity5 to 85% (no condensation)*1
Ambient temperature for storage-20 to +50°C*1
Allowable power flicker time2 ms (When in use. In normal situations, this conforms to the CPU unit.)
Operating environmentMinimal amount of dust and corrosive gas present
Noise immunity1,500 Vp-p, pulse width : 1 µs, 50 ns (by way of a noise simulator)
Withstand voltage1,500 VAC for 1 minute between the power supply terminal and the I/O terminals and between all the external terminals and the case
Insulation resistance50 MΩ or more (tested with a 500 VDC megger, between the PLC power supply terminal and the I/O terminals and between all the external terminals and the case)
Vibration resistanceIntermittent vibrationFrequency: 10 to 57 HzAmplitude : 0.075 mm*3
Frequency: 57 to 150 HzAcceleration : 9.8 m/s2*3
Continuous vibrationFrequency: 10 to 57 HzAmplitude : 0.035 mm*3
Frequency: 57 to 150 HzAcceleration : 4.9 m/s2*3
Performance specificationsPositioning controlNumber of control axes2-axis simultaneous (linear interpolation, circular interpolation), 2-axis independent
Cumulative address-2,147,483,648 to +2,147,483,647 pulses (2 to the power of 32)
Positioning controlPositioning modeAbsolute coordinate, relative coordinate, speed control to positioning, positioning to speed control, speed control (only during independent operation)
Position setting range±99,999,999
Startup timeIndependent operation : 1.1 ms, linear interpolation : 1.8 ms, circular interpolation : 2.1 ms
M-codeNumber 1 to 255, WITH/AFTER mode
Origin returnOrigin return methodThere are two types of origin returning operations : high-speed returning (which does not require the sensor in front of the origin) and origin returning that shares the CCW limit switch and the origin sensor. Origin detection can be set to the AND condition of the origin sensor and the Z-phase. There is a function for automatically returning to the origin when the power is turned on. There is a function for automatic travel to the home position when the origin returning operation completes.
High-speed counterSigned 24-bit (counts from -8,388,608 to +8,388,607) × 2, each of the 2 comparators has a fractional coordinate transformation function, speed changing by way of comparator matching, deceleration stop, fixed dimension feeding deceleration stop
Applicable PLCsKV-700
Maximum number of series connectable units48 maximum (For 16 units or more, extension units are necessary.)
Number of memory points400 (for each axis)
Occupied deviceFor each unit : input : 5 channels, output : 5 channels, arbitrary data registers (data memory) : 280 words
Position setting unitsmm, angle, number of pulses, fractional coordinate transformation unit, decimal point position : digit 0 to 7
Speed setting range1 to 500,000 p/s : automatic trapezoid, cosine, second-order curve, third-order curve, parabola acceleration and deceleration (the starting speed is 0 to 500,000 p/s); 1 to 99,999,999 when the setting unit is mm/s or deg/s
Acceleration/deceleration setting range1 to 65000 mm/s/ms, deg/s/ms, p/s/ms
Acceleration/deceleration control unitsAcceleration : 1 ms, deceleration : 2 ms
Continuous operationStandby after deceleration, start immediately after deceleration, consecutive acceleration and deceleration without deceleration
Pulse output formatLine driver output, 1/2 pulse method
External interfaceInput : 24 VDC, photocoupler input; output : open-collector output (30 VDC, 300 mA), no overcurrent protection circuit
5 V power source5 V ±10%, 100 mA maximum (when 24 VDC is applied to input connectors 13 and 14)
Sensor positioningPositioning to an arbitrary point through the use of a stop sensor
PalletizingRepeated addition of relative amount, return function
Error indicationOutput of error details to the KZ-HP1 or CPU unit
Self-diagnosisDiagnoses can be performed according to hardware errors, various parameter errors, error numbers, and messages.
Data backupEEPROM rewritable 100,000 times. Electric double-layer capacitors are used to hold the current coordinate and current value of the high-speed counter for 2 months (at 25°C). Parameters that are changed by the PLC are written to the EEPROM the next time that the power is turned on.
TeachingCurrent coordinate teaching using JOG travel, direct teaching using the current counter value, external teaching from a PLC
Power flicker detectionStops operation when a power flicker error is detected
Parameter settingsThis is also possible by way of setting the data memory and controlling the relays of the KZ-HP1 teaching unit or of the dedicated parameter settings monitor software.
Internal current consumptionMain unit side : 185 mA (280 mA when the KZ-HP1 is connected), I/O side : 150 mA
WeightApprox 200g

Lựa chọn PLC phù hợp với Module keyence

SKUMô tả
CPU
KV-8000CPU unit
KV-7300CPU unit with built-in serial port
KV-7500CPU unit with built-in EtherNet/IP® port
KV-1000CPU unit with built-in serial port
KV-3000CPU unit with built-in serial port
KV-5000CPU unit with built-in Ethernet port
KV-5500CPU unit with built-in EtherNet/IP® port
KV-700CPU unit with built-in serial port
I/O unit
KV-B16RA16-point Screw Terminal Block, Relay Output
KV-B16RC16-point Screw Terminal Block, Relay Output
KV-B16TA16-point Screw Terminal Block, Transistor (Sink)
KV-B16TC16-point Screw Terminal Block, Transistor (Sink)
KV-B16TCP16-point Screw Terminal Block, Transistor (Source)
KV-B16TD16-point Screw Terminal Block, MOSFET (Sink) with Overcurrent Protection
KV-B16XA16-point Screw Terminal Block
KV-B16XC16-point Screw Terminal Block
KV-B8RC8-point Screw Terminal Block, Relay Output (Independent Common)
KV-B8XTD8-point/8-point Screw Terminal Block, MOSFET (Sink), with Overcurrent Protection
KV-C16XTD16-point/16-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C32TA32-point Connector Transistor (Sink)
KV-C32TC32-point Connector Transistor (Sink)
KV-C32TCP32-point Connector Transistor (Source)
KV-C32TD32-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C32XA32-point Connector
KV-C32XC32-point Connector
KV-C32XTD32-point/32-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C64TA64-point Connector Transistor (Sink)
KV-C64TC64-point Connector Transistor (Sink)
KV-C64TCP64-point Connector Transistor (Source)
KV-C64TD64-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C64XA64-point Connector
KV-C64XB64-point Connector, with All Terminals Supporting 2-wire Sensors
KV-C64XC64-point Connector
KV-SIR32XTHigh speed I/O unit
I/O unit/Remote I/O unit
KV-N16ERExpansion output unit, output 16 points, relay output, screw terminal block
KV-N16ETExpansion output unit 16 Outputs Transistor (Sink) Output Screw Terminal Block,
KV-N16ETPExpansion output unit 16-output Transistor (source) output Screw terminal block
KV-N16EXExpansion unit, Input, 16 points, 5/24 VDC switchable, screw terminal block
KV-N8ERExpansion output unit, output 8 points, relay output, screw terminal block
KV-N8ETExpansion output unit 8 Outputs Transistor (Sink) Output Screw Terminal Block,
KV-N8ETPExpansion output unit 8-output Transistor (source) output Screw terminal block
KV-N8EXExpansion Input Unit DC Input 8 Points Type Screw Terminal Block
KV-N8EXRExpansion I/O Unit 16 Points Type Screw Terminal Block, Input(8 Points) relay output(8 Points)
KV-N8EXTExpansion I/O Unit Screw Terminal Block, Screw Terminal Block, Input(8 Points) Transistor (sink)(8 Points)
KV-NC16ETExpansion Output Unit 16-output Transistor (Sink) connector type
KV-NC16ETEExpansion output unit 16 outputs transistor (sink) output European terminal block
KV-NC16ETPExpansion output unit 16-output Transistor (source) output Connector type
KV-NC16ETPEExpansion output unit 16 outputs transistor (source) output European terminal block
KV-NC16EXExpansion Input Unit 16-input switching 5V/24V DC connector type
KV-NC16EXEExpansion input unit input 16 points European terminal block
KV-NC16EXTExpansion I/O unit 32-point connector type 16-input, 16-output (transistor)
KV-NC32ETExpansion Output Unit 32-output Transistor (Sink) connector type
KV-NC32ETPExpansion output unit 32-output Transistor (source) output Connector type
KV-NC32EXExpansion Input Unit 32-input switching 5V/24V DC connector type
KV-NC32EXTExpansion I/O unit 32-input 32-output Transistor (sink) output Connector type
KV-NC8ERExpansion Output Unit 8-output Relay connector type
Analog/Temperature unit
KV-AD40A/D Conversion Unit, 4 Analog Input Channels
KV-AD40GHigh-precision A/D Conversion Unit, 4 Analog Input Channels
KV-AD40VA/D Conversion Unit, 4 Analog Input Channels
KV-AM40VA/D D/A Conversion Unit, 2 Analog Input Channels + 2 Analog Output Channels
KV-DA40D/A Conversion Unit, 4 Analog Output Channels
KV-DA40VD/A Conversion Unit, 4 Analog Output Channels
KV-SAD04High-speed analogue input unit
KV-SDA04High-speed analogue output unit
KV-TF40PID Temperature Adjustment Unit (Multi-input 4-channel)
KV-TP40Temperature Analog Multi-input Unit (Multi-input 4-channel)
Analog/Temperature unit/Remote I/O unit
KV-N3AMAnalog I/O Unit, voltage and current Input 2ch, voltage and current Output 1ch
KV-NC2DAD/A conversion unit (2 points)
KV-NC4ADA/D Conversion Unit 4-point type
KV-NC4TPTemperature 4-input unit
Remote I/O unit
KL-16BR16-point Screw Terminal Block, Relay Output
KL-16BT16-point Screw Terminal Block, Transistor (Sink)
KL-16BX16-point Screw Terminal Block
KL-16CT16-point Connector Transistor (Sink)
KL-16CX16-point Connector
KL-2DAD/A Conversion Unit, 2 Analog Output Channels
KL-2TFPID Temperature Adjustment Unit (2-channel)
KL-32CT32-point Connector Transistor (Sink)
KL-32CX32-point Connector
KL-4ADA/D Conversion Unit, 4 Analog Input Channels
KL-8BLR8-point Screw Terminal Block, Relay Output with Repeater Function
KL-8BLT8-point Screw Terminal Block, Transistor (Sink) Output, with Repeater Function
KL-8BLX8-point Screw Terminal Block with Repeater Function
KL-8BXR8 Input + 8 Relay Output Screw Terminal Block
KL-8BXT8 Input + 8 Transistor (Sink) Output Screw Terminal Block
KL-B1Joint Cable Adapter
KL-DC1ADC Current Input Unit
KL-DC1VDC Voltage Input Unit
KL-LC1Load Cell Measurement Unit
KL-N20VKL Master Unit
KL-T1T-shaped Branch Unit
KL-WH1Power Measurement Unit
KV-EP02EtherNet/IP® Compatible Communication Unit
KV-RC16BR16-point Screw Terminal Block, Relay Output, with Repeater Function
KV-RC16BT16-point Screw Terminal Block, Transistor Output, with Repeater Function
KV-RC16BX16-point Screw Terminal Block Input, with Repeater Function
KV-RC16BXT16-input + 16-output Screw Terminal Block, Transistor Output
KV-RC32BT32-point Screw Terminal Block, Transistor Output
KV-RC32BX32-point Screw Terminal Block Input
KV-RC8BXR8-input + 8-output Screw Terminal Block, Relay Output, with Repeater Function
KV-RC8BXT8-input + 8-output Screw Terminal Block, Transistor Output, with Repeater Function
Positioning/Motion unit
KV-H20G2-axis Pulse Train (Linear and Circular Interpolation and Synchronous Operation Possible) with Built-in 2-channel High-speed Counter
KV-H20S2-axis Pulse Train (Linear Interpolation Possible)
KV-H40S4-axis Pulse Train (Linear Interpolation Possible)
KV-MC20V2-axis Pulse Train Positioning Motion Unit
KV-MC40V4-axis Pulse Train Positioning Motion Unit
KV-ML16V16-axis ML 2-compatible Positioning Motion Unit
KV-MX1INC Encoder, 4 Input Channels, 12 Inputs, 12 Outputs, SD Card
KV-SH04PLHigh-Speed Positioning Unit
KV-XH04ML4-Axis Positioning/Motion Unit
KV-XH16ML16-Axis Positioning/Motion Unit
Highspeed counter unit
KV-SC20V2-channel Multi-function High-speed Counter Unit
KV-SSC02High speed counter unit
Information/Network unit
KV-CL20Master/Local Unit
KV-DN20DeviceNet® Unit
KV-EP21VEtherNet/IP® Unit
KV-FL20VFL-net Unit
KV-L20VSerial Communication Unit
KV-L21VSerial Communication Unit
KV-LE20VEthernet Unit
KV-LE21VEthernet Unit
KV-LH20VCommunication Positioning Unit
KV-LM20VHigh-speed Multi-link (Megalink) Unit
KV-LM21VHigh-speed multi-link Unit
KV-XL202Serial communication unit, 2 ports (RS-232C×2)
KV-XL402Serial communication unit, 2 ports (RS-422A/485×2)
KV-XLE02EtherNet unit, 2 ports
Power/Bus connection unit
KV-7000CBus Connection Unit
KV-EB1Extension Unit
KV-N1Conversion unit with connector unit
KV-NC1Conversion unit with terminal block connector
KV-PU1AC Power Supply Unit with Error Output

Thông tin bổ sung

Thương hiệu
Series
Yêu cầu tư vấn0983 995 440(Call/Zalo)

Có thể bạn thích…

Cam kết và hỗ trợ

Luôn có giá tốt nhất thị trường
Giao hàng trên toàn quốc
Hỗ trợ dịch vụ kỹ thuật

Khu vực Miền Nam

Call: 0386 334 447 / Chat Zalo zalo

Khu vực Miền Bắc

Call: 0384 988 968 / Chat Zalo zalo

Khu vực Miền Trung

Call: 0374 687 899 / Chat Zalo zalo

Dịch vụ kỹ thuật/Bảo hành

Call: 0348 957 778 / Chat Zalo zalo

Email liên hệ

sale.haiautech@gmail.com

Dịch vụ cung ứng sản phẩm

Vì sản phẩm đa dạng, nếu Quý khách chưa tìm được. Vui lòng liên hệ để được hỗ trợ.

Tư vấn lựa chọn hoặc chuyển đổi
Nhập khẩu thiết bị theo yêu cầu

dich-vu-sua-chua-bien-tan-thiet-bi-tu-dong-hoa