| Product characteristics |
|---|
| Output signal | switching signal; IO-Link; (configurable) |
| Measuring range | | -1…10 bar | -14.5…145 psi | -100…1000 kPa | -0.1…1 MPa |
|
| Process connection | threaded connection 1/4″ NPT external thread internal thread:M5 |
| Application |
|---|
| Measuring element | metallic thin film cell |
| Application | for industrial applications |
| Media | liquids and gases |
| Medium temperature [°C] | -40…90 |
| Min. bursting pressure | |
| Pressure rating | |
| Note on pressure rating | |
| Vacuum resistance [mbar] | -1000 |
| Type of pressure | relative pressure |
| MAWP (for applications according to CRN) [bar] | 25 |
| Electrical data |
|---|
| Operating voltage [V] | 18…30 DC |
| Current consumption [mA] | < 15 |
| Min. insulation resistance [MΩ] | 100; (500 V DC) |
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | < 0.3 |
| Inputs / outputs |
|---|
| Number of inputs and outputs | Number of digital outputs: 2 |
| Outputs |
|---|
| Total number of outputs | 2 |
| Output signal | switching signal; IO-Link; (configurable) |
| Electrical design | PNP/NPN |
| Number of digital outputs | 2 |
| Output function | normally open / normally closed; (parameterisable) |
| Max. voltage drop switching output DC [V] | 2 |
| Permanent current rating of switching output DC [mA] | 100 |
| Switching frequency DC [Hz] | < 170 |
| Short-circuit protection | yes |
| Type of short-circuit protection | pulsed |
| Overload protection | yes |
| Measuring/setting range |
|---|
| Measuring range | | -1…10 bar | -14.5…145 psi | -100…1000 kPa | -0.1…1 MPa |
|
| Set point SP | | -0.9…10 bar | -13.1…145 psi | -0.09…1 MPa |
|
| Reset point rP | | -0.95…9.95 bar | -13.8…144.3 psi | -0.095…0.995 MPa |
|
| In steps of | | 0.005 bar | 0.1 psi | 0.0005 MPa |
|
| Factory setting | | SP1 = 2.5 bar | rP1 = 2.3 bar | ou1 = Hno; | | SP2 = 7.5 bar | rP2 = 7.3 bar | ou2 = Hno; | | dS1/dS2 = 0 ms | dr1/dr2 = 0 ms | | | coF = 0 % | P-n = PnP | dAP= 60 ms |
|
| Accuracy / deviations |
|---|
| Switch point accuracy [% of the span] | < ± 0,5 (nach DIN EN 61298-2) |
| Repeatability [% of the span] | < ± 0,05; (with temperature fluctuations < 10 K) |
| Characteristics deviation [% of the span] | < ± 0,5 (nach DIN EN 61298-2); (incl. drift when overtightened, zero point and span error, non-linearity, hysteresis) |
| Linearity deviation [% of the span] | < ± 0,1 (BFSL) / < ± 0,2 (LS) |
| Hysteresis deviation [% of the span] | < ± 0,2 |
| Long-term stability [% of the span] | < ± 0,1; (per 6 months) |
| Temperature coefficient zero point [% of the span / 10 K] | < 0,1 (-25…90 °C) / < 0,2 (-40…-25 °C) |
| Temperature coefficient span [% of the span / 10 K] | < 0,1 (-25…90 °C) / < 0,2 (-40…-25 °C) |
| Response times |
|---|
| Response time [ms] | < 3 |
| Software / programming |
|---|
| Parameter setting options | hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping |
| Interfaces |
|---|
| Communication interface | IO-Link |
| Transmission type | COM2 (38,4 kBaud) |
| IO-Link revision | 1.1 |
| SDCI standard | IEC 61131-9 |
| Profiles | Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis |
| SIO mode | yes |
| Required master port type | A |
| Process data analogue | 2 |
| Process data binary | 2 |
| Min. process cycle time [ms] | 5 |
| Supported DeviceIDs | | Type of operation | DeviceID | | Default | 855 |
|
| Operating conditions |
|---|
| Ambient temperature [°C] | -40…90 |
| Storage temperature [°C] | -40…100 |
| Protection | IP 67; IP 69K |
| Mechanical data |
|---|
| Weight [g] | 66 |
| Materials | 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI |
| Materials (wetted parts) | stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630) |
| Min. pressure cycles | 60 million; (at 1.2 times nominal pressure) |
| Tightening torque [Nm] | 50; (recommended tightening torque; depends on lubrication, seal and pressure rating) |
| Process connection | threaded connection 1/4″ NPT external thread internal thread:M5 |
| Restrictor element integrated | yes |
| Remarks |
|---|
| Remarks | | BFSL = Best Fit Straight Line | | LS = limit value setting |
|
| Pack quantity | 1 pcs. |
| Electrical connection |
|---|
| Connection | Connector: 1 x M12 |
