| Product characteristics | |||||
|---|---|---|---|---|---|
| Number of inputs and outputs | Number of digital outputs: 2; Number of analogue outputs: 1 | ||||
| Measuring range [l/min] | 0.2…150 | ||||
| Process connection | G 1 DN25 flat seal | ||||
| Application | |||||
| Special feature | Gold-plated contacts | ||||
| Media | conductive liquids; water; hydrous media | ||||
| Note on media |
| ||||
| Medium temperature [°C] | -20…90 | ||||
| Pressure rating [bar] | 16 | ||||
| Pressure rating [Mpa] | 1.6 | ||||
| Electrical data | |||||
| Operating voltage [V] | 18…30 DC; (according to EN 50178 SELV/PELV) | ||||
| Current consumption [mA] | < 80 | ||||
| Protection class | III | ||||
| Reverse polarity protection | yes | ||||
| Power-on delay time [s] | 5 | ||||
| Inputs / outputs | |||||
| Number of inputs and outputs | Number of digital outputs: 2; Number of analogue outputs: 1 | ||||
| Inputs | |||||
| Inputs | counter reset | ||||
| Outputs | |||||
| Total number of outputs | 2 | ||||
| Output signal | switching signal; analogue signal; pulse signal; IO-Link; frequency signal; (configurable) | ||||
| Electrical design | PNP/NPN | ||||
| Number of digital outputs | 2 | ||||
| Output function | normally open / normally closed; (parameterisable) | ||||
| Max. voltage drop switching output DC [V] | 2 | ||||
| Permanent current rating of switching output DC [mA] | 100 | ||||
| Number of analogue outputs | 1 | ||||
| Analogue current output [mA] | 4…20; (scalable) | ||||
| Max. load [Ω] | 500 | ||||
| Pulse output | flow rate meter | ||||
| Short-circuit protection | yes | ||||
| Type of short-circuit protection | pulsed | ||||
| Overload protection | yes | ||||
| Measuring/setting range | |||||
| Measuring range [l/min] | 0.2…150 | ||||
| Display range [l/min] | -180…180 | ||||
| Resolution [l/min] | 0.1 | ||||
| Set point SP [l/min] | 1…150 | ||||
| Reset point rP [l/min] | 0.2…149.2 | ||||
| Analogue start point ASP [l/min] | 0…120 | ||||
| Analogue end point AEP [l/min] | 30…150 | ||||
| Low flow cut-off LFC [l/min] | 0.2…7.5 | ||||
| Frequency end point, FEP [l/min] | 30.2…150 | ||||
| Frequency at the end point FRP [Hz] | 1…10000 | ||||
| Volumetric flow quantity monitoring | |||||
| Pulse length [s] | 0.002…2 | ||||
| Pulse value | 0.001…99990000 I | ||||
| Temperature monitoring | |||||
| Measuring range [°C] | -20…90 | ||||
| Display range [°C] | -42…112 | ||||
| Resolution [°C] | 0.1 | ||||
| Set point SP [°C] | -19.6…90 | ||||
| Reset point rP [°C] | -20…89.6 | ||||
| Analogue start point [°C] | -20…68 | ||||
| Analogue end point [°C] | 2…90 | ||||
| In steps of [°C] | 0.1 | ||||
| Accuracy / deviations | |||||
| Flow monitoring | |||||
| Accuracy (in the measuring range) | ± (0,8 % MW + 0,2 % MEW) | ||||
| Repeatability | ± 0,2 % MEW | ||||
| Temperature monitoring | |||||
| Accuracy [K] | ± 2,5 (Q > 5 % MEW) | ||||
| Response times | |||||
| Flow monitoring | |||||
| Start-up delay [s] | 0…50 | ||||
| Response time [s] | < 0.25; (dAP = 0, T09) | ||||
| Damping for the switching output dAP [s] | 0…5 | ||||
| Temperature monitoring | |||||
| Response time [s] | 15; (Q > 10 % MEW, T09) | ||||
| Software / programming | |||||
| Parameter setting options | hysteresis / window; normally open / normally closed; switching logic; frequency output; current/pulse output; start-up delay; display can be deactivated; Display unit | ||||
| Interfaces | |||||
| Communication interface | IO-Link | ||||
| Transmission type | COM2 (38,4 kBaud) | ||||
| IO-Link revision | 1.1 | ||||
| SDCI standard | IEC 61131-9 | ||||
| Profiles | Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis | ||||
| SIO mode | yes | ||||
| Required master port type | A | ||||
| Process data analogue | 3 | ||||
| Process data binary | 2 | ||||
| Min. process cycle time [ms] | 6 | ||||
| Supported DeviceIDs |
| ||||
| Operating conditions | |||||
| Ambient temperature [°C] | -20…60 | ||||
| Storage temperature [°C] | -25…80 | ||||
| Protection | IP 65; IP 67 | ||||
| Mechanical data | |||||
| Weight [g] | 787.5 | ||||
| Materials | stainless steel (1.4408/316); stainless steel (1.4404 / 316L); PC; PBT+PC-GF30 | ||||
| Materials (wetted parts) | stainless steel (1.4404 / 316L); PEEK; carbon fibre PEEK; EPDM; Centellen | ||||
| Process connection | G 1 DN25 flat seal | ||||
| Displays / operating elements | |||||
| Display |
| ||||
| Remarks | |||||
| Remarks |
| ||||
| Pack quantity | 1 pcs. | ||||
| Electrical connection | |||||
| Connection | Connector: 1 x M12; Contacts: gold-plated | ||||
Cảm biến lưu lượng IFM SM8120 16 bar
SKU: SM8120
Hãng sản xuất: IFM
Chất lượng: Mới 100%
Bảo hành: Chính hãng
Chứng từ: CO/CQ, hóa đơn VAT
Khu vực Miền Nam
Call: 0345 177 768 / Chat Zalo 
Khu vực Miền Bắc
Call: 0384 988 968 / Chat Zalo
Khu vực Miền Trung
Call: 0374 687 899 / Chat Zalo
Dịch vụ kỹ thuật/Bảo hành
Call: 0348 957 778 / Chat Zalo
Email liên hệ
Dịch vụ cung ứng sản phẩm
Vì sản phẩm đa dạng, nếu Quý khách chưa tìm được. Vui lòng liên hệ để được hỗ trợ.
Tư vấn lựa chọn hoặc chuyển đổi
Nhập khẩu thiết bị theo yêu cầu
