Module Keyence KL-DC1V

Khối điện áp ngõ vào DC
SKU: KL-DC1V
Hãng sản xuất: Keyence
Chất lượng: Mới 100%
Bảo hành: Chính hãng
Chứng từ: hóa đơn VAT

Dịch vụ kèm theo:
✓ Lập trình & Sửa chữa PLC Keyence theo yêu cầu
✓ Lắp đặt & vận hành tận nơi
✓ Hỗ trợ kỹ thuật trọn đời

Báo giá

Mã: KL-DC1V Danh mục: PLC, PLC Keyence

Mô tả
Thông tin bổ sung

Model				KL-DC1V
General specifications	Measurement type			DC voltage
	Power voltage			24 VDC ± 10%, Class 2
	Operating ambient temperature			0 to +50°C (no freezing)
	Operating ambient humidity			35 to 85%RH(no condensation)
	Ambient temperature for storage			-20 to +70°C
	Operating environment			Minimal amount of dust and corrosive gas present
	Measurement category			III
	Wire temperature rating			+60°C or more
	Noise immunity			1,500 Vp-p or more, pulse width: 1 µs, 50 ns (by way of a noise simulator), conforms to IEC standards (IEC 61000-4-2/-3/-4/-6)
	Withstand voltage			1,500 VAC for 1 minute (between the power supply terminal and each terminal and between all the terminals and the case)
	Insulation resistance			100 MΩ or more (tested with a 500 VDC megger, between the power supply terminal and each I/O terminal and between all the terminals and the case)
	Internal current consumption (excluding current for driving input circuits)			170mA or less
	Shock resistance			Conforms to JIS B 3502 and IEC 61131-2, 147 m/s², operating time: 11 ms, 3 times in each of the 3 directions
	Pollution degree			2
	Vibration resistance	Intermittent vibration	Frequency: 10 to 57 Hz	Amplitude: 0.075 mm^*1
			Frequency: 57 to 150 Hz	Acceleration: 9.8 m/s²^*1
		Continuous vibration	Frequency: 10 to 57 Hz	Amplitude: 0.035 mm^*1
			Frequency: 57 to 150 Hz	Acceleration: 4.9 m/s²^*1
	Weight			approx 350g
Performance specifications	Number of channels			1CH
	Number of ranges			3
	Range switching			Setting: Use the setting switch. Connection: The connection terminal varies depending on the range.
	Input method			Single-ended
	Sampling rate			Normal mode: 1 ms (1,000 times/sec.), high-precision mode: 100 ms (10 times/sec.)
	Input range^*2			Range 1: 0 to 10 V, range 2: ±10 V, range 3: ±100 V^*2
	Displayable range	Range 1: 0 to 20 mA		0.000 to 10.999V^*3
		Range 2: ±10 mA		-10.999 to 10.999V^*3
		Range 3: ±100 mA		-109.99 to 109.99V^*3
	Resolution	Normal	Range 1: 0 to 20 mA	1 mV (0.001 V; 1/10000)^*4
			Range 2: ±10 mA	1mV(0.001V)1/20000^*2
			Range 3: ±100 mA	10mV(0.01V)1/20000^*2
		High accuracy	Range 1: 0 to 20 mA	100 µV (0.1 mV; 1/100000)^*2
			Range 2: ±10 mA	100 µV (0.1 mV; 1/200000)^*2
			Range 3: ±100 mA	1mV(0.001V)1/200000^*2
	Input impedance	Range 1: 0 to 20 mA		1 MΩ
		Range 2: ±10 mA
		Range 3: ±100 mA		4 MΩ
	Absolute maximum input current	Range 1: 0 to 20 mA		±100 V
		Range 2: ±10 mA
		Range 3: ±100 mA		±150 V
	Measurement accuracy (25 ±5°C)	Range 1: 0 to 20 mA		±0.1% of F.S. ± 1 digit
		Range 2: ±10 mA
		Range 3: ±100 mA		±0.2% of F.S. ± 1 digit
	Measurement accuracy (0 to 50°C)	Range 1: 0 to 20 mA		±0.5% of F.S. ± 1 digit
		Range 2: ±10 mA
		Range 3: ±100 mA		±0.6% of F.S. ± 1 digit
	Control input			2 (Parameters are used to switch between the KL input, peak/bottom hold control input, and 0-point adjustment input.)
	Controloutput			2 transistor (NPN open-collector) outputs (Parameters are used to switch between the KL output and comparator output.)
	Setting data			Recorded to the EEPROM (rewritable 1,000,000 times)
	Other functions			Hold (peak and bottom), 0-point adjustment, comparator output, filter setting (LPF and HPF), time average (simple and moving), scaling setting, display unit changing, lock
Control I/O specifications	External calibration input signal	Number of inputs		2
		Maximum input voltage		DC26.4V
		Input rated voltage		DC24V 5.3mA
		Minimum ON voltage		19V
		Maximum OFF current		1.5mA
		Common ground		2/common
		Input time constant		10ms
	Control output	Number of outputs		2
		Output		Transistor NPN output
		Rated load		DC30V 0.1A
		Peak load current		0.2A
		Leakage current (at OFF)		100 µA or less
		Residual voltage (at ON)		DC0.8V or less
		Common ground		2/common
		ON/OFF response time		Off to on: 10 µs or less (between 5 and 100 mA), on to off: 50 µs or less (between 5 and 100 mA)
KL link specifications	Supported master units			Model: KL-N20V, supported PLC: KEYENCE KV-1000/700; model: KL-N10V, supported PLC: KEYENCE KV-10/16/24/40; model: KV-P16*L (built-in PLC), supported PLC: KEYENCE; model: KL-N20A, supported PLC: Mitsubishi AnA, AnA, AnU, QnA, AnSH, and Q2AS; model: KL-N20C, supported PLC: Omron C200H/HS, SYSMAC α, and CS1 (excluding the C200H-02/22), KEYENCE VT2-12F/10F/10T/10S/8T/8S/7S/5T/5S/5M and DT-100
	Communication address			00 H to FE H(0 to 254)
	Number of occupied words			EASY mode: reception (KL to PLC): 5 words, transmission (PLC to KL): 3 words; FULL mode: reception (KL to PLC): 7 words, transmission (PLC to KL): 5 words^*5
	Communication speed			2.5 Mbps, 625 kbps, 156 kbps (set with parameters)^*6
^1 Conforms to JIS B 3502, IEC61131-2Number of sweeps: 10 times respectively in the X, Y, and Z directions (80 minutes)^2 Select with the setting switch.^3 Even if a voltage that exceeds the input range has been input, if it is within the displayable range, it will be displayed (up to 10,999 can be displayed with an absolute value). In this case, display will be performed from the lowest digit; the upper 2 digits will be displayed with A flashing. (Ex: When using 10.500 V input with a range of 2 (input range ±10 V), A.500 is displayed) If a voltage that exceeds the displayable range has been input, FFFF (-FFFF) will be displayed. Also, when scaling is in effect, if the measurement value exceeds the displayable range with an input voltage in the input range, EFFF (-EFFF) will be displayed.^4 When scaling is enabled, the maximum resolution is 0.5 mV (1/20000).^5 In the direction of transmission/reception when seen from the master unit.^6 The > do not support a communication speed of 5 Mbps.

Lựa chọn PLC phù hợp với Module keyence

SKU	Mô tả
CPU
KV-8000	CPU unit
KV-7300	CPU unit with built-in serial port
KV-7500	CPU unit with built-in EtherNet/IP® port
KV-1000	CPU unit with built-in serial port
KV-3000	CPU unit with built-in serial port
KV-5000	CPU unit with built-in Ethernet port
KV-5500	CPU unit with built-in EtherNet/IP® port
KV-700	CPU unit with built-in serial port
I/O unit
KV-B16RA	16-point Screw Terminal Block, Relay Output
KV-B16RC	16-point Screw Terminal Block, Relay Output
KV-B16TA	16-point Screw Terminal Block, Transistor (Sink)
KV-B16TC	16-point Screw Terminal Block, Transistor (Sink)
KV-B16TCP	16-point Screw Terminal Block, Transistor (Source)
KV-B16TD	16-point Screw Terminal Block, MOSFET (Sink) with Overcurrent Protection
KV-B16XA	16-point Screw Terminal Block
KV-B16XC	16-point Screw Terminal Block
KV-B8RC	8-point Screw Terminal Block, Relay Output (Independent Common)
KV-B8XTD	8-point/8-point Screw Terminal Block, MOSFET (Sink), with Overcurrent Protection
KV-C16XTD	16-point/16-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C32TA	32-point Connector Transistor (Sink)
KV-C32TC	32-point Connector Transistor (Sink)
KV-C32TCP	32-point Connector Transistor (Source)
KV-C32TD	32-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C32XA	32-point Connector
KV-C32XC	32-point Connector
KV-C32XTD	32-point/32-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C64TA	64-point Connector Transistor (Sink)
KV-C64TC	64-point Connector Transistor (Sink)
KV-C64TCP	64-point Connector Transistor (Source)
KV-C64TD	64-point Connector MOSFET (Sink) with Overcurrent Protection
KV-C64XA	64-point Connector
KV-C64XB	64-point Connector, with All Terminals Supporting 2-wire Sensors
KV-C64XC	64-point Connector
KV-SIR32XT	High speed I/O unit
I/O unit/Remote I/O unit
KV-N16ER	Expansion output unit, output 16 points, relay output, screw terminal block
KV-N16ET	Expansion output unit 16 Outputs Transistor (Sink) Output Screw Terminal Block,
KV-N16ETP	Expansion output unit 16-output Transistor (source) output Screw terminal block
KV-N16EX	Expansion unit, Input, 16 points, 5/24 VDC switchable, screw terminal block
KV-N8ER	Expansion output unit, output 8 points, relay output, screw terminal block
KV-N8ET	Expansion output unit 8 Outputs Transistor (Sink) Output Screw Terminal Block,
KV-N8ETP	Expansion output unit 8-output Transistor (source) output Screw terminal block
KV-N8EX	Expansion Input Unit DC Input 8 Points Type Screw Terminal Block
KV-N8EXR	Expansion I/O Unit 16 Points Type Screw Terminal Block, Input(8 Points) relay output(8 Points)
KV-N8EXT	Expansion I/O Unit Screw Terminal Block, Screw Terminal Block, Input(8 Points) Transistor (sink)(8 Points)
KV-NC16ET	Expansion Output Unit 16-output Transistor (Sink) connector type
KV-NC16ETE	Expansion output unit 16 outputs transistor (sink) output European terminal block
KV-NC16ETP	Expansion output unit 16-output Transistor (source) output Connector type
KV-NC16ETPE	Expansion output unit 16 outputs transistor (source) output European terminal block
KV-NC16EX	Expansion Input Unit 16-input switching 5V/24V DC connector type
KV-NC16EXE	Expansion input unit input 16 points European terminal block
KV-NC16EXT	Expansion I/O unit 32-point connector type 16-input, 16-output (transistor)
KV-NC32ET	Expansion Output Unit 32-output Transistor (Sink) connector type
KV-NC32ETP	Expansion output unit 32-output Transistor (source) output Connector type
KV-NC32EX	Expansion Input Unit 32-input switching 5V/24V DC connector type
KV-NC32EXT	Expansion I/O unit 32-input 32-output Transistor (sink) output Connector type
KV-NC8ER	Expansion Output Unit 8-output Relay connector type
Analog/Temperature unit
KV-AD40	A/D Conversion Unit, 4 Analog Input Channels
KV-AD40G	High-precision A/D Conversion Unit, 4 Analog Input Channels
KV-AD40V	A/D Conversion Unit, 4 Analog Input Channels
KV-AM40V	A/D D/A Conversion Unit, 2 Analog Input Channels + 2 Analog Output Channels
KV-DA40	D/A Conversion Unit, 4 Analog Output Channels
KV-DA40V	D/A Conversion Unit, 4 Analog Output Channels
KV-SAD04	High-speed analogue input unit
KV-SDA04	High-speed analogue output unit
KV-TF40	PID Temperature Adjustment Unit (Multi-input 4-channel)
KV-TP40	Temperature Analog Multi-input Unit (Multi-input 4-channel)
Analog/Temperature unit/Remote I/O unit
KV-N3AM	Analog I/O Unit, voltage and current Input 2ch, voltage and current Output 1ch
KV-NC2DA	D/A conversion unit (2 points)
KV-NC4AD	A/D Conversion Unit 4-point type
KV-NC4TP	Temperature 4-input unit
Remote I/O unit
KL-16BR	16-point Screw Terminal Block, Relay Output
KL-16BT	16-point Screw Terminal Block, Transistor (Sink)
KL-16BX	16-point Screw Terminal Block
KL-16CT	16-point Connector Transistor (Sink)
KL-16CX	16-point Connector
KL-2DA	D/A Conversion Unit, 2 Analog Output Channels
KL-2TF	PID Temperature Adjustment Unit (2-channel)
KL-32CT	32-point Connector Transistor (Sink)
KL-32CX	32-point Connector
KL-4AD	A/D Conversion Unit, 4 Analog Input Channels
KL-8BLR	8-point Screw Terminal Block, Relay Output with Repeater Function
KL-8BLT	8-point Screw Terminal Block, Transistor (Sink) Output, with Repeater Function
KL-8BLX	8-point Screw Terminal Block with Repeater Function
KL-8BXR	8 Input + 8 Relay Output Screw Terminal Block
KL-8BXT	8 Input + 8 Transistor (Sink) Output Screw Terminal Block
KL-B1	Joint Cable Adapter
KL-DC1A	DC Current Input Unit
KL-DC1V	DC Voltage Input Unit
KL-LC1	Load Cell Measurement Unit
KL-N20V	KL Master Unit
KL-T1	T-shaped Branch Unit
KL-WH1	Power Measurement Unit
KV-EP02	EtherNet/IP® Compatible Communication Unit
KV-RC16BR	16-point Screw Terminal Block, Relay Output, with Repeater Function
KV-RC16BT	16-point Screw Terminal Block, Transistor Output, with Repeater Function
KV-RC16BX	16-point Screw Terminal Block Input, with Repeater Function
KV-RC16BXT	16-input + 16-output Screw Terminal Block, Transistor Output
KV-RC32BT	32-point Screw Terminal Block, Transistor Output
KV-RC32BX	32-point Screw Terminal Block Input
KV-RC8BXR	8-input + 8-output Screw Terminal Block, Relay Output, with Repeater Function
KV-RC8BXT	8-input + 8-output Screw Terminal Block, Transistor Output, with Repeater Function
Positioning/Motion unit
KV-H20G	2-axis Pulse Train (Linear and Circular Interpolation and Synchronous Operation Possible) with Built-in 2-channel High-speed Counter
KV-H20S	2-axis Pulse Train (Linear Interpolation Possible)
KV-H40S	4-axis Pulse Train (Linear Interpolation Possible)
KV-MC20V	2-axis Pulse Train Positioning Motion Unit
KV-MC40V	4-axis Pulse Train Positioning Motion Unit
KV-ML16V	16-axis ML 2-compatible Positioning Motion Unit
KV-MX1	INC Encoder, 4 Input Channels, 12 Inputs, 12 Outputs, SD Card
KV-SH04PL	High-Speed Positioning Unit
KV-XH04ML	4-Axis Positioning/Motion Unit
KV-XH16ML	16-Axis Positioning/Motion Unit
Highspeed counter unit
KV-SC20V	2-channel Multi-function High-speed Counter Unit
KV-SSC02	High speed counter unit
Information/Network unit
KV-CL20	Master/Local Unit
KV-DN20	DeviceNet® Unit
KV-EP21V	EtherNet/IP® Unit
KV-FL20V	FL-net Unit
KV-L20V	Serial Communication Unit
KV-L21V	Serial Communication Unit
KV-LE20V	Ethernet Unit
KV-LE21V	Ethernet Unit
KV-LH20V	Communication Positioning Unit
KV-LM20V	High-speed Multi-link (Megalink) Unit
KV-LM21V	High-speed multi-link Unit
KV-XL202	Serial communication unit, 2 ports (RS-232C×2)
KV-XL402	Serial communication unit, 2 ports (RS-422A/485×2)
KV-XLE02	EtherNet unit, 2 ports
Power/Bus connection unit
KV-7000C	Bus Connection Unit
KV-EB1	Extension Unit
KV-N1	Conversion unit with connector unit
KV-NC1	Conversion unit with terminal block connector
KV-PU1	AC Power Supply Unit with Error Output